The Pentair ScreenLogic integration allows you to integrate your Pentair IntelliTouch or EasyTouch pool controller with Home Assistant via the Pentair ScreenLogic gateway.

Configuration

The ScreenLogic®Interface Wireless Connection interface consists of an indoor and outdoor wireless 902-928 MHz wireless transceiver. Note: The wireless transceivers ship from the factory as a matched pair. The ID numbers on each transceiver must be the same number to function correctly. If needed, the transceivers are replaced as a matched pair. In this video we go over how to operate the Pentair Screenlogic connect app, the different screens of screenlogic connect, also known as screenlogic 2 Screen.

Adding Pentair ScreenLogic to your Home Assistant instance can be done via the userinterface, by using this My button:

Pentair ScreenLogic can be auto-discovered by Home Assistant. If an instance was found,it will be shown as “Discovered”, which you can select to set it up rightaway.

If there wasn’t any discovered automatically, don’t worry! You can set up amanual integration entry:

Browse to your Home Assistant instance.
In the sidebar click on Configuration.
From the configuration menu select: Integrations.
In the bottom right, click on theAdd Integration button.
From the list, search and select “Pentair ScreenLogic”.
Follow the instruction on screen to complete the set up.

Options

ScreenLogic options are set via Configuration -> Integrations -> Pentair ScreenLogic -> Options.

Seconds between scans - How many seconds between each polling of the ScreenLogic gateway.

Pentair Screenlogic Support

Services

screenlogic.set_color_mode

Sets the operation of any connected color-capable lights.

Service data attribute	Optional	Description
`target`	no	An `area` containing the ScreenLogic device, the ScreenLogic `device` itself, or any `entity` from the ScreenLogic device you wish to set the color mode on.
`color_mode`	no	The color mode to set. Valid values are listed below.

Pentair Screenlogic Not Connecting

Reference

Pentair Screenlogic Api

Color Modes

color_mode	Name	Description
`all_off`	All Off	Turns all light circuits off.
`all_on`	All On	Turns all light circuits on to their last mode.
`color_set`	Color Set	Sets light circuits to their pre-set colors as set in the pool controller.
`color_sync`	Color Sync	Synchronize all IntelliBrite, SAm, SAL, or FIBERworks color changing lights and synchronize their colors.
`color_swim`	Color Swim	Cycles through white, magenta, blue and green colors. (Emulates Pentair SAm color changing light.)
`party`	Party	Rapid color changing building the energy and excitement.
`romance`	Romance	Slow color transitions creating a mesmerizing and calming effect.
`caribbean`	Caribbean	Transitions between a variety of blues and greens.
`american`	American	Patriotic red, white and blue transition.
`sunset`	Sunset	Dramatic transitions of orange, red and magenta tones.
`royal`	Royal	Richer, deeper, color tones.
`save`	Save Color	Save the exact colors that are being displayed.
`recall`	Recall Color	Recall the saved colors.
`blue`	Blue	Fixed color: Blue
`green`	Green	Fixed color: Green
`red`	Red	Fixed color: Red
`white`	White	Fixed color: White
`magenta`	Magenta	Fixed color: Magenta
`thumper`	Thumper	Toggles the solenoid thumper on MagicStream laminars.
`next_mode`	Next Mode	Cycle to the next color mode.
`reset`	Reset	Reset light modes.
`hold`	Hold	Hold light transitions.

Help us to improve our documentation
Suggest an edit to this page, or provide/view feedback for this page.

Verify the wireless router Power LEDin on. These two devices should be located near one another. Cycle the power to both of these devices. You can use a paper clip to reset the Protocol Adapter by pressing the recessed reset button.

Using paintbrush in word. Click to see full answer.

In respect to this, how do I update my Pentair ScreenLogic?

STEP 1: UPDATE YOUR PROTOCOL ADAPTERThe firmware version can be found on the label on the side of the protocol adapter. ScreenLogic is available for your iOS and Android devices. Please visit the Apple App Store or Google Play Store. Download the Protocol Adapter update tool (available for PC and Mac):

Also Know, how do I reset my Pentair protocol adapter? You can use a paper clip to reset the Protocol Adapter by pressing the recessed reset button. You canunplug and plug back in the wireless router to reset it. 3. Verify the wiring to the protocol adapter and IntelliTouch Load Center.

Similarly one may ask, what is Pentair ScreenLogic?

The ScreenLogic Interface Wireless Bundle combines the protocol adapter and Wireless Link into one convenient package. The ScreenLogic 2 User Interface enables users to control their pool and spa features using wireless devices including Android, Apple iPhone, iPod Touch, iPad, MAC, PC and Microsoft Windows Computers.

What is Pentair egg timer?

Pentair Screenlogic Download

Use the Egg Timer circuit. to set an automatic shut-off time. The time period can be anywhere from 1 minute to 24 hours. The Egg Timer is. also a useful feature for turning off lighting and spa jets.